| Line 53: | Line 53: | ||
</pre> | </pre> | ||
| + | ===Zones=== | ||
| + | Special Zones: | ||
| + | * DROP | ||
| + | |||
| + | Groups that usually exist by default: | ||
| + | * Internal | ||
| + | * Public | ||
==Custom Services== | ==Custom Services== | ||
| Line 102: | Line 109: | ||
| − | === | + | ===Port Forwarding To Other IP=== |
<pre>firewall-cmd --zone=external --add-forward-port=port=22:proto=tcp:toport=10.1.2.3:12345 (--permanent)</pre> | <pre>firewall-cmd --zone=external --add-forward-port=port=22:proto=tcp:toport=10.1.2.3:12345 (--permanent)</pre> | ||
Revision as of 16:24, 20 July 2021
Contents
Quick Set
Make Permanent
firewall-cmd --runtime-to-permanent
or
firewall-cmd --add-service=xxx --premanent
-note: Making a change with "permanent" is not immediately active.
Reset To Perm Rules
firewall-cmd --reload
List Stuff
firewall-cmd --list-all-zones
firewall-cmd --zone={zone} --list-all
Add / Remove Stuff
Add
firewall-cmd --add-service=
firewall-cmd --add-port= {n}/{tcp|udp}
firewall-cmd --add-protocol= {protocol name, eg: smb2}
Remove
firewall-cmd --remove ...
Zones
firewall-cmd --get-zones
firewall-cmd --get-active-zones
firewall-cmd --set-default-zone={zone}
firewall-cmd --zone={zone} --add-interface={ifname}
firewall-cmd --zone={zone} --change-interface={ifname}
firewall-cmd --zone={zone} --remove-interface={ifname}
firewall-cmd --zone={zone} --query-interface={ifname}
Default Zone: If no zone is specified, the default zone is assumed.
To set a target zone for subsequent commands, declare a target zone:
firewall-cmd --set-target=DROP firewalld-cmd --~blablabla~
Zones
Special Zones:
- DROP
Groups that usually exist by default:
- Internal
- Public
Custom Services
Clone/add and edit here: /usr/lib/firewalld/services
<?xml version="1.0" encoding="utf-8"?> <service> <short>SSH</short> <port protocol="tcp" port="22"/> </service>
ICMP Inversion
What is blocked is allowed. What is allowed is blocked. Enable to allow all ICMP.
firewall-cmd --zone=drop --add-icmp-block-inversion --permanent
ICMP Stuff
firewall-cmd --get-icmptypes firewall-cmd --info-icmptype=<icmptype> firewall-cmd --query-icmp-block=<icmptype> firewall-cmd --add-icmp-block=<icmptype> firewall-cmd --remove-icmp-block=<icmptype>
ICMP Services
firewall-cmd --get-icmptypes
address-unreachable bad-header communication-prohibited destination-unreachable echo-reply echo-request fragmentation-needed host-precedence-violation host-prohibited host-redirect host-unknown host-unreachable ip-header-bad neighbour-advertisement neighbour-solicitation network-prohibited network-redirect network-unknown network-unreachable no-route packet-too-big parameter-problem port-unreachable precedence-cutoff protocol-unreachable redirect required-option-missing router-advertisement router-solicitation source-quench source-route-failed time-exceeded timestamp-reply timestamp-request tos-host-redirect tos-host-unreachable tos-network-redirect tos-network-unreachable ttl-zero-during-reassembly ttl-zero-during-transit unknown-header-type unknown-option
Masquerade & Forwarding
Forwarding requires masquerading being turned on!
Masquerading
firewall-cmd --add-masquerade
firewall-cmd --remove-masquerade
firewall-cmd --zone {zone} --query-masquerade
Port Forwarding
firewall-cmd --zone=external --add-forward-port=port=22:proto=tcp:toport=12345 (-–permanent)
Port Forwarding To Other IP
firewall-cmd --zone=external --add-forward-port=port=22:proto=tcp:toport=10.1.2.3:12345 (--permanent)
Lockdown
Lockdown prevents changes to the firewall by services.
firewall-cmd --lockdown=on
Allowing services individually...
# firewall-cmd --add-lockdown-whitelist-command='/usr/bin/python -Es /usr/bin/firewall-cmd*' [--permanent]
CONFIG
/etc/firewalld/firewalld.conf
DefaultZone=dmz
/etc/sysconfig/network-scripts/ifcfg-xxx
ZONE=public