(Created page with "STP: 802.1d RSTP: 802.1w MSTP: 802.1s Due to PVST's existance, STP is referred to as Common STP (CST) sometimes. == STP 802.1d == Bridge ID: * Priority . MAC * 0..65536 in 4...") |
|||
| (One intermediate revision by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | STP: 802.1d | + | STP: 802.1d<br/> |
| − | RSTP: 802.1w | + | RSTP: 802.1w<br/> |
| − | MSTP: 802.1s | + | MSTP: 802.1s<br/> |
Due to PVST's existance, STP is referred to as Common STP (CST) sometimes. | Due to PVST's existance, STP is referred to as Common STP (CST) sometimes. | ||
| Line 14: | Line 14: | ||
* Priority . Port # | * Priority . Port # | ||
* 0..255 | * 0..255 | ||
| + | * 128 default | ||
| + | * lower is better | ||
Path Determination: | Path Determination: | ||
| Line 63: | Line 65: | ||
! global portfast | ! global portfast | ||
sw(config)# spanning-tree portfast default </nowiki> | sw(config)# spanning-tree portfast default </nowiki> | ||
| − | |||
== RSTP 802.1w == | == RSTP 802.1w == | ||
Latest revision as of 11:01, 4 December 2012
STP: 802.1d
RSTP: 802.1w
MSTP: 802.1s
Due to PVST's existance, STP is referred to as Common STP (CST) sometimes.
STP 802.1d
Bridge ID:
- Priority . MAC
- 0..65536 in 4096 increments
- 32768 default
- lower is better
Port ID:
- Priority . Port #
- 0..255
- 128 default
- lower is better
Path Determination:
- cost
- BID
- PID
Port Roles:
- Root Port: egress port to the root bridge
- Designated Port: ingress port to the root bridge
- Blocking Port: all packets but ingress BPDU dropped
All ports on a Root Bridge are Designated ports.
Port States:
- Blocking
- Listening
- Learning
- Forwarding
Convergence time:
- 20 sec: BLK (MaxAge) time
- 15 sec: Listening time
- 15 sec: Learning time
Default timers:
- Hello: 2 sec
- MaxAge: 10x Hello
- FWD delay: 15 sec (listen & learn time)
Notes:
- Load balancing based on VLANs is typically done by adjusting port priority. This is not done if etherchannel bonded.
- After determining a root bridge, BPDUs are only sent by the root bridge.
Cisco:
! set bridge priority sw(config)# spanning-tree (vlan [list]) priority # ! set priority macro ! primary: 24576 or 4096 lower than lowest discovered but always > 0 ! secondary: 28672 or 4096 lower than second lowest discovered sw(config)# spanning-tree (vlan [list]) root [primary | secondary] ! set port priority sw(config-if)# spanning-tree vlan # portpriority [0..255] ! set cost sw(config)# spanning-tree vlan # cost # ! global portfast sw(config)# spanning-tree portfast default
RSTP 802.1w
BPDUs are sent by all switches. This allows a topology to be determined.
Port Roles:
- Root Port: egress to root bridge
- Designated Port: ingress to root bridge
- Alternate Port: alternate egress to root bridge (directly connected to root)
- Backup Port: alternate port not connected to root bridge
Port States:
- Discarding: listening, learning, and discarding non-BPDU packets
- Forwarding: forwarding of course
Port Types:
- Edge Port: a port connected to an end device (Cisco: a port in portfast mode)
- Root Port: the best egress port to the root
- Point-to-Point Port: link between two segments (seems to be just a logical definition of a port)
Default Timers:
- Hello: 2 sec
- Dead: 3x Hello (drops neighborship after this time)
Cisco:
! set p2p link sw(config-if)# spanning-tree link-type point-to-point
MSTP 802.1s
Aggregates STP instances under one process. This is done on a switch by switch basis and is transparent to other switches.
PV(R)STP(+)
This is all Cisco proprietary:
PVSTP: It introduced PortFast, BackboneFast (alternates for DESG failures), and UplinkFast (alternates for ROOT failures). It required ISL trunks.
PVSTP+: Basicly, PVSTP with 802.1q. This is the default mode on Cisco switches. The VLAN ID is added to the priority. That's why there's a 4096 incrementor value. BPDUs are transmitted over links untagged.
PVRSTP+: Just RSTP + PVSTP+.
Cisco Crap
Cisco switches only support these modes:
- PVSTP+ : #spanning-tree mode pvst
- PVRSTP+ : #spanning-tree mode rapid-pvst
- MSTP : #spanning-tree mode mst
.