From wikistone
Jump to: navigation, search
 
(2 intermediate revisions by the same user not shown)
Line 1: Line 1:
 +
==tcpdump==
 +
tcpdump -vv -x -X -s 1500 -i eth1 'port 25'
 +
 
==arping==
 
==arping==
 
Use arping to get L2 and L3 responses.<br>
 
Use arping to get L2 and L3 responses.<br>
Line 4: Line 7:
 
Some files here: http://www.habets.pp.se/synscan/files/ .<br>
 
Some files here: http://www.habets.pp.se/synscan/files/ .<br>
  
−
==use==
+
===use===
 
Make sure to pick an interface with an IP. Interface is required, but IP is not. If no IP, it will use 0.0.0.0 unless otherwise specified.<br>
 
Make sure to pick an interface with an IP. Interface is required, but IP is not. If no IP, it will use 0.0.0.0 unless otherwise specified.<br>
  
Line 25: Line 28:
 
</pre>
 
</pre>
  
−
==man page==
+
===man page===
 
<pre>
 
<pre>
 
arping(8)
 
arping(8)
Line 43: Line 46:
 
       -b    Send only MAC level broadcasts. Normally arping starts from sending broadcast, and switch to unicast after reply received.
 
       -b    Send only MAC level broadcasts. Normally arping starts from sending broadcast, and switch to unicast after reply received.
  
−
       Stop after sending count ARP REQUEST
+
       -c count
 +
              Stop after sending count ARP REQUEST
 
               packets. With deadline [arping(8)] option, arping waits for count ARP REPLY packets, until the timeout expires.
 
               packets. With deadline [arping(8)] option, arping waits for count ARP REPLY packets, until the timeout expires.
  
Line 50: Line 54:
 
       -f    Finish after the first reply confirming that target is alive.
 
       -f    Finish after the first reply confirming that target is alive.
  
−
       Name of network device where to send ARP REQUEST packets.
+
       -I interface
 +
              Name of network device where to send ARP REQUEST packets.
  
 
       -h    Print help page and exit.
 
       -h    Print help page and exit.
Line 56: Line 61:
 
       -q    Quiet output. Nothing is displayed.
 
       -q    Quiet output. Nothing is displayed.
  
−
       IP source address to use in ARP packets.
+
       -s source
 +
              IP source address to use in ARP packets.
 
               If this option is absent, source address is:
 
               If this option is absent, source address is:
−
 
 
               · In DAD mode (with option -D) set to 0.0.0.0.
 
               · In DAD mode (with option -D) set to 0.0.0.0.
−
 
 
               · In Unsolicited ARP mode (with options -U or -A) set to destination.
 
               · In Unsolicited ARP mode (with options -U or -A) set to destination.
−
 
 
               · Otherwise, it is calculated from routing tables.
 
               · Otherwise, it is calculated from routing tables.
  
Line 69: Line 72:
 
       -V    Print version of the program and exit.
 
       -V    Print version of the program and exit.
  
−
       Specify a timeout, in seconds, before
+
       -w deadline
 +
              Specify a timeout, in seconds, before
 
               arping  exits  regardless of how many packets have been sent or received. In this case arping does not stop after count [arping(8)] packet are sent,  
 
               arping  exits  regardless of how many packets have been sent or received. In this case arping does not stop after count [arping(8)] packet are sent,  
 
               it waits either for deadline [arping(8)] expire or until count [arping(8)] probes are answered.
 
               it waits either for deadline [arping(8)] expire or until count [arping(8)] probes are answered.

Latest revision as of 18:25, 13 March 2014

tcpdump

tcpdump -vv -x -X -s 1500 -i eth1 'port 25'

arping

Use arping to get L2 and L3 responses.

Some files here: http://www.habets.pp.se/synscan/files/ .

use

Make sure to pick an interface with an IP. Interface is required, but IP is not. If no IP, it will use 0.0.0.0 unless otherwise specified.

Send ARP request:

# arping -I enp4s0 -c 2 10.0.0.1
ARPING 10.0.0.1 from 10.0.0.42 enp4s0
Unicast reply from 10.0.0.1 [AA:BB:CC:DD:EE:FF]  1.199ms
Unicast reply from 10.0.0.1 [AA:BB:CC:DD:EE:FF]  1.045ms
Sent 2 probes (1 broadcast(s))
Received 2 response(s)

Dup IP check:

# arping -D -I enp4s0 -c 3 10.0.0.1
ARPING 10.0.0.1 from 0.0.0.0 enp4s0
Unicast reply from 10.0.0.1 [AA:BB:CC:DD:EE:FF]  0.888ms
Sent 1 probes (1 broadcast(s))
Received 1 response(s)

man page

arping(8)

NAME
       arping - send ARP REQUEST to a neighbour host

SYNOPSIS
       arping [-AbDfhqUV] [-c count] [-w deadline] [-s source] {-I interface} {destination}

DESCRIPTION
       Ping destination on device interface by ARP packets, using source address source.

OPTIONS
       -A     The same as -U, but ARP REPLY packets used instead of ARP REQUEST.

       -b     Send only MAC level broadcasts. Normally arping starts from sending broadcast, and switch to unicast after reply received.

       -c count
              Stop after sending count ARP REQUEST
              packets. With deadline [arping(8)] option, arping waits for count ARP REPLY packets, until the timeout expires.

       -D     Duplicate address detection mode (DAD). See RFC2131, 4.4.1 ⟨http://tools.ietf.org/rfc/rfc2131.txt⟩ .  Returns 0, if DAD succeeded i.e. no replies are received

       -f     Finish after the first reply confirming that target is alive.

       -I interface
              Name of network device where to send ARP REQUEST packets.

       -h     Print help page and exit.

       -q     Quiet output. Nothing is displayed.

       -s source
              IP source address to use in ARP packets.
              If this option is absent, source address is:
              · In DAD mode (with option -D) set to 0.0.0.0.
              · In Unsolicited ARP mode (with options -U or -A) set to destination.
              · Otherwise, it is calculated from routing tables.

       -U     Unsolicited ARP mode to update neighbours' ARP caches.  No replies are expected.

       -V     Print version of the program and exit.

       -w deadline
              Specify a timeout, in seconds, before
              arping  exits  regardless of how many packets have been sent or received. In this case arping does not stop after count [arping(8)] packet are sent, 
              it waits either for deadline [arping(8)] expire or until count [arping(8)] probes are answered.

SEE ALSO
       ping(8)[Cross reference to non-existant ID “ping”], clockdiff(8)[Cross reference to non-existant ID “clockdiff”], tracepath(8)[Cross reference to non-existant ID “tracepath”].

AUTHOR
       arping was written by Alexey Kuznetsov kuznet@ms2.inr.ac.ru ⟨mailto:kuznet@ms2.inr.ac.ru⟩ .  It is now maintained by YOSHIFUJI Hideaki yoshfuji@skbuff.net ⟨mailto:yoshfuji@skbuff.net⟩ .

SECURITY
       arping requires CAP_NET_RAW capability to be executed. It is not recommended to be used as set-uid root, because it allows user to modify ARP caches of neighbour hosts.

AVAILABILITY
       arping is part of iputils package and the latest versions are available in source form at ⟨http://www.skbuff.net/iputils/iputils-current.tar.bz2⟩.

iputils-                                                                                         13 August 2013                                                                              arping(8)